Back to UTEC Home Page | Back to UTEC Product Information Back to UTEC Home Page | Back to UTEC Product Information
High Tear Resistance Oil Resistant Non Marring
High Load Bearing Capacity Excellent Flex Life Non Shrapnellizing
Excellent Vibration Dampening Easy Installation Close Center to Center Distance
High Loads per 1/8" Deflection
Short Run or Slow Speed - Up to 200 strokes per hour - above 25% of spring height*
Intermittent Speed - Up to 700 strokes per hour - up to 25% of spring height*
Continuous Speed - Up to 12,000 strokes per hour - up to 15% of spring height*
*For Optimum Life
Bandsawing - Use any type conventional saw with 4 hook(sharp) carbon blade with raker set
Lathe Cutting - use H.S.S. Tool Bits with positive rake from 5 to 10 degrees
Shearing - Consult factory, recommended medium to high production cutting
Heat buildup is a major cause of premature breakdown. This is a direct function of effective strokes per hour and % deflection of the urethane. Always select spring that will give minimum deflection % for job.
The closeness two or more springs can be placed. Urethane springs and strippers can not be placed side by side; since urethanes are non compressible. When squeezed, the o.d. of the spring must be free to bulge to allow for the displaced urethane by the reduction in height of the spring or stripper. In the case of Tool-A-Thane Springs and Strippers the amount of the area left available is a function of the size of the springs and the amount of the deflection Normally 1/8" to 3/16" must be left around the O.D. of a spring.
Other shapes than tubes can be used for developing pressures. Bar stock and Sheets are used where pressures above 2600#/1/8" deflection are required. Consult factory for further data or assistance for determining these requirements.
Consult Catalog for available standard sizes, loads per 1/8" deflection, and prices.
Consult factory for non standard sizes and their pricing.
Catalog and/or Price List shows all prices for Tool-A-Thane Urethane Springs & Strippers for sizes below. Standard grades are: UT-25 90 Durometer Shore A Black UT-15 95 Durometer Shore A Black UT-35 85 Durometer Shore A Black UT-5 75 Durometer Shore D Black Other grades and hardnesses from 35 Durometer Shore A thru 75 Durometer Shore D available. Consult factory for pricing and delivery on made to order grades and hardnesses.
________________TOOL-A-THANE_URETHANE_SPRINGS________________
CATALOG________”A”___________”B”__________”C”________________
NUMBER_________I.D.__________O.D.________LENGTH______________
250L1 1/4” 3/4” 1 ”
250L2 1/4” 3/4” 1-1/4”
250L3 1/4” 3/4” 1-1/2”
250L4 1/4” 3/4” 1-3/4”
250L0 1/4” 3/4” 6 ”
375L1 3/8” 7/8” 1 ”
375L2 3/8” 7/8” 1-1/4”
375L3 3/8” 7/8” 1-1/2”
375L4 3/8” 7/8” 1-3/4”
375L5 3/8” 7/8” 2 ”
375LX 3/8” 7/8” 12 ”
500L1 1/2” 1 ” 1 ”
500L2 1/2” 1 ” 1-1/4”
500L3 1/2” 1 ” 1-1/2”
500L4 1/2” 1 ” 1-3/4”
500L5 1/2” 1 ” 2 ”
500LX 1/2” 1 ” 12 ”
625L1 5/8” 1-1/8” 1 ”
625L2 5/8” 1-1/8” 1-1/4”
625L3 5/8” 1-1/8” 1-1/2”
625L4 5/8” 1-1/8” 1-3/4”
625L5 5/8” 1-1/8” 2 ”
625LX 5/8” 1-1/8” 12 ”
750L1 3/4” 1-3/8” 1-1/4”
750L2 3/4” 1-3/8” 1-1/2”
750L3 3/4” 1-3/8” 1-3/4”
750L4 3/4” 1-3/8” 2 ”
750L5 3/4” 1-3/8” 2-1/4”
750LX 3/4” 1-3/8” 12 ”
100L1 1 ” 1-3/4” 1-1/4”
100L2 1 ” 1-3/4” 1-1/2”
100L3 1 ” 1-3/4” 1-3/4”
100L4 1 ” 1-3/4” 2 ”
100L5 1 ” 1-3/4” 2-1/4”
100L6 1 ” 1-3/4” 2-1/2”
100L7 1 ” 1-3/4” 2-3/4”
100LX 1 ” 1-3/4” 12 ”
250M1 1/4” 7/8” 1 ”
250M2 1/4” 7/8” 1-1/4”
250M3 1/4” 7/8” 1-1/2”
250M4 1/4” 7/8” 1-3/4”
250M0 1/4” 7/8” 6 ”
375M1 3/8” 1 “ 1 ”
375M2 3/8” 1 “ 1-1/4”
375M3 3/8” 1 “ 1-1/2”
375M4 3/8” 1 “ 1-3/4”
375M5 3/8” 1 “ 2 ”
375MX 3/8” 1 “ 12 ”
500M1 1/2” 1-1/8” 1 ”
500M2 1/2” 1-1/8” 1-1/4”
500M3 1/2” 1-1/8” 1-1/2”
500M4 1/2” 1-1/8” 1-3/4”
500M5 1/2” 1-1/8” 2 ”
500MX 1/2” 1-1/8” 12 ”
625M1 5/8” 1-1/4” 1 ”
625M2 5/8” 1-1/4” 1-1/4”
625M3 5/8” 1-1/4” 1-1/2”
625M4 5/8” 1-1/4” 1-3/4”
625M5 5/8” 1-1/4” 2 ”
|
________________TOOL-A-THANE_URETHANE_SPRINGS________________
CATALOG________”A”___________”B”__________”C”________________
NUMBER_________I.D.__________O.D.________LENGTH______________
625MX 5/8” 1-1/4” 12 ”
750M1 3/4” 1-1/2” 1-1/4”
750M2 3/4” 1-1/2” 1-1/2”
750M3 3/4” 1-1/2” 1-3/4”
750M4 3/4” 1-1/2” 2 ”
750M5 3/4” 1-1/2” 2-1/4”
750M6 3/4” 1-1/2” 2-1/2”
750M7 3/4” 1-1/2” 2-3/4”
750MX 3/4” 1-1/2” 12 ”
100M1 1 ” 2 ” 1-1/4”
100M2 1 ” 2 ” 1-1/2”
100M3 1 ” 2 ” 1-3/4”
100M4 1 ” 2 ” 2 ”
100M5 1 ” 2 ” 2-1/4”
100M6 1 ” 2 ” 2-1/2”
100M7 1 ” 2 ” 2-3/4”
100M8 1 ” 2 ” 3 ”
100M9 1 ” 2 ” 4 ”
100MX 1 ” 2 ” 12 ”
250H1 1/4” 1 ” 1 ”
250H2 1/4” 1 ” 1-1/4”
250H3 1/4” 1 ” 1-1/2”
250H4 1/4” 1 ” 1-3/4”
250H0 1/4” 1 ” 6 ”
375H1 3/8” 1-1/8” 1 ”
375H2 3/8” 1-1/8” 1-1/4”
375H3 3/8” 1-1/8” 1-1/2”
375H4 3/8” 1-1/8” 1-3/4”
375H5 3/8” 1-1/8” 2 ”
375HX 3/8” 1-1/8” 12 ”
500H1 1/2” 1-1/4” 1 ”
500H2 1/2” 1-1/4” 1-1/4”
500H3 1/2” 1-1/4” 1-1/2”
500H4 1/2” 1-1/4” 1-3/4”
500H5 1/2” 1-1/4” 2 ”
500HX 1/2” 1-1/4” 12 ”
625H1 5/8” 1-3/8” 1 ”
625H2 5/8” 1-3/8” 1-1/4”
625H3 5/8” 1-3/8” 1-1/2”
625H4 5/8” 1-3/8” 1-3/4”
625H5 5/8” 1-3/8” 2 ”
625HX 5/8” 1-3/8” 12 ”
750H1 3/4” 1-3/4” 1-1/4”
750H2 3/4” 1-3/4” 1-1/2”
750H3 3/4” 1-3/4” 1-3/4”
750H4 3/4” 1-3/4” 2 ”
750H5 3/4” 1-3/4” 2-1/4”
750H6 3/4” 1-3/4” 2-1/2”
750H7 3/4” 1-3/4” 2-3/4”
750HX 3/4” 1-3/4” 12 ”
100H1 1 ” 2-1/2” 1-1/4”
100H2 1 ” 2-1/2” 1-1/2”
100H3 1 ” 2-1/2” 1-3/4”
100H4 1 ” 2-1/2” 2 ”
100H5 1 ” 2-1/2” 2-1/4”
100H6 1 ” 2-1/2” 2-1/2”
100H7 1 ” 2-1/2” 2-3/4”
100H8 1 ” 2-1/2” 3 ”
100H9 1 ” 2-1/2” 4 ”
100HX 1 ” 2-1/2” 12 ” |
For prices Cick here: TOOL-A-THANE Springs and Strippers